dis for general
Quiz yourself by thinking what should be in
each of the black spaces below before clicking
on it to display the answer.
Help!
|
|
||||
|---|---|---|---|---|---|
| What method of magnetic particle inspection is used most often to inspect aircraft parts for invisible cracks and other defects | continuous
🗑
|
||||
| What metal has special short-time heat properties and is used in the construction of aircraft firewalls? | titanium alloy
🗑
|
||||
| If it is necessary to accurately measure the diameter of a hole approximately 1/4 inch in diameter, the mechanic should use a___ | small-hole gauge
🗑
|
||||
| Which heat-treating operation would be performed when the surface of the metal is changed chemically by introducing a high carbide or nitride content? | case hardening
🗑
|
||||
| (1) An aircraft part may be demagnetized by subjecting it to a magnetizing force from alternating current that is gradually reduced in strength. (2) An aircraft part may be demagnetized by subjecting it to a magnetizing force from direct current that is | Both 1 and 2 are true
🗑
|
||||
| When the specific torque value for nuts is not given, where can the recommended torque value be found? | in AC 43.13-1B on page 7-9
🗑
|
||||
| Dividers do not _______ when they are used as a measuring device | provide a reading
🗑
|
||||
| What is descriptive of the annealing process of steel during and after it has been annealed? | Slow cooling and low strength
🗑
|
||||
| When performing a dye penetrant inspection, what does the developer do? | Acts as a blotter to produce a visible indication
🗑
|
||||
| What two types of indicating mediums (materials) are available for magnetic particle inspection? | Wet and dry process materials
🗑
|
||||
| What is the pattern for an inclusion is a magnetic particle buildup forming? | parallel lines.
🗑
|
||||
| What tool is generally used to set a divider to an exact precise dimension? | A machinist scale
🗑
|
||||
| Circular magnetization of a part can be used to detect which defects? | defects parallel to the long axis of the part
🗑
|
||||
| Which condition indicates a part has cooled too quickly after being welded? | Cracking adjacent to the weld
🗑
|
||||
| Residual magnetizing inspection method may be used with what material? | Steels that have been heat treated
🗑
|
||||
| What precision measuring tool is used for measuring crankpin and main bearing journals for out-of-round wear? |
🗑
|
||||
| a T-Gauge is also called what? (im putting this cause i didnt know and it annoyed me) | telescopic gauge
🗑
|
||||
| What defects are not acceptable for metal lines? | 1. Cracked flare
2. Seams
3. Dents in the heel of a bend less than 20% of the diameter
5. Dents in straight section that are 20% of tube diameter
🗑
|
||||
| A part which is being prepared for dye penetrant inspection should be cleaned with | Volatile petroleum-based solvent to make them as cleaned as posible
🗑
|
||||
| In examining and evaluating a welded joint, a mechanic should be familiar with | ambient exposure conditions,
intended use of the part,
type of weld, and
original part material composition.
🗑
|
||||
| What aluminum alloy designations indicate that the metal has received no hardening or tempering treatment? H36, O, or F | F means 'as fabricated.' There has been no control over its temper.
🗑
|
||||
| Normalizing is a process of heat treating what? | Iron-base metal only
🗑
|
||||
| Magnetic particle inspection is used primarily to detect defects where? | detect flaws on or near the surface
🗑
|
||||
| Aircraft bolts are usually manufactured with what type of class fit? | Class 3 which is medium fit. It is used on almost all standard aircraft bolts.
🗑
|
||||
| Which material cannot be heat treated repeatedly without harmful effects? | Clad aluminum alloy.
🗑
|
||||
| Which tool is used to find the center of a shaft or other cylindrical work? | Combination set.
🗑
|
Review the information in the table. When you are ready to quiz yourself you can hide individual columns or the entire table. Then you can click on the empty cells to reveal the answer. Try to recall what will be displayed before clicking the empty cell.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
Wolfbane507
Popular Aviation sets