Oxygen Therapy Word Scramble
|
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
| Question | Answer |
| What is the goal of oxygen therapy? | To maintain adequate tissue oxygenation while minimizing cardiopulmonary work. |
| What are the objectives of oxygen therapy? | To treat hypoxemia. To decrease symptoms of hypoxemia To decrease cardiopulmonary workload. |
| How do you assess need of oxygen therapy? | Assess ABG Assess underlying problem or condition. (history) Physical Assessment |
| It is important to beware of conflicting information. You must always... | Treat the patient and not the numbers |
| What are the hazards of oxygen therapy? | oxygen toxicity Depression of ventilatory drive absorption atelectasis Bronchopulmonary dysplasia retrolental fibroplasia |
| What is oxygen toxicity? | High exposure to oxygen that results in an increased concentration of oxygen and causes and over production of free radicals that damage the epithelial tissues. |
| What are two factors that contribute to oxygen toxicity? | Fi02 and exposure time |
| What does oxygen toxicity primarily affect? | The lungs and CNS CNS- tremors, twitching, convulsions PNS- Pneumonia, Pulmonary fibrosis |
| What is absorption atelectasis? | Nitrogen washout, damage to type II pneumocytes |
| What is Bronchopulmonary dysplasia? | (BPD) is found in premature babies |
| What is retrolental fibroplasia? | scar tissue in the eyes |
| What is considered a high oxygen concentration? | A concentration greater than 60%. |
| What are the two oxygen delivery systems? | Low Flow Systems High Flow Systems |
| Low flow systems | have variable FI02 Does not meet the patients flow rate demand FI02 is just an estimate |
| What are some examples of a low flow system? | Nasal Cannula Reservoir Cannulas Nasal Catheter Transtracheal oxygen simple mask Partial rebreathing mask non-rebreating mask |
| High flow systems | Fixed FI02 Meets patient's flow rate demand |
| High Flow system examples | Air entrainment mas i.e. Venturi Mask Air Entrainment Nebulizer |
| What's special about the nasal cannula? | It's the most commonly used oxygen therapy device |
| The nasal cannula handles flow rates | up to 6 Liters/Minute (adult) |
| Estimating Fi02 with nasal cannula | 1 L/minute=24% Fi02 Each additional liter increases Fi02 4% |
| In nasal cannulas can you use a bubble humidifier? | Yes, at flow rates set at 4 L/min and greater |
| Are pediatric and infant sizes available in the nasal cannula? | yes |
| What's a special nasal cannula? | Reservoir cannulas (conserving devices) They suppliment the fi02 and are rarely seen |
| Is there a high flow nasal cannula? | Yes it is rarely seen and it comes with a special bubble humidifier that can handle high flow. |
| Nasal cannulas replaced what device? | Nasal catheters |
| Nasal catheters can handle flow rates up to? | 6L/Minute |
| Estimating percentage of nasal cannulas | 1 L/minute=24% fio2 Each additional liter increases Fi02 4% |
| The bubble humidifiers are used for flow rates | Set at 4L/min and greater |
| Are there pediatric and infant sizes available for nasal catheters? | Yes |
| Transtracheal oxygen is | inconspicuous/ Rare Is designed for long term oxygen therapy. Commonly used with a bubble humidifier. |
| Why is the transtracheal oxygen more efficient than a nasal cannula? | Oxygen delivery directly to the trachea. |
| What happens to flow rates? | They can be reduced by 50% |
| What are disadvantages to transtracheal oxygen? | Requires a minor surgery Infection Bleeding Subcutaneous emphysema Must be cleaned frequently damage to catheter requires replacement over time. Not covered by all insurance agencies |
| The simple mask is | More commonly used by EMT's |
| What are the flow rate requirements? | 6-10 liters per minute |
| What fi02 values can the simple mask achieve | 35%-50% |
| Can a bubble humidifier be used with a simple mask? | Yes but the flow rate requirement for the simple mask is 6 L/minute and you do not want the bubble humidifer to go past 6 or 7 or it will alarm |
| Are there pediatric sizes available for the simple mask? | Yes |
| What is the difference between an aerosol mask/simple mask? | The aerosol mask has larger holes on the side. The simple mask have small holes on the side. |
| What are the two types of rebreathing masks? | Non-Rebreathing/Partial rebreathing mask |
| What does the non-rebreathing mask have? | 2 check valves |
| What are the flow rate requirements for the non-rebreathing mask? | Enough to keep the bag inflated |
| What fi02 values can be achieved with the non-rebreathing mask? | 60-80% |
| Can a bubble humidifier be used with both rebreathing masks?? | yes |
| Are pediatric sizes available? | yes |
| What is the flow rate requirement for partial-rebreathing masks? | enough to keep the bag inflated |
| What fi02 values can the partial rebreather mask achieve? | 40-60% |
| Are pediatric sized available in the partial-rebreathing mask? | yes |
| Does the partial rebreathing mask have check valves? | no |
| What are factors that alter the performance of low flow systems and increase the Fi02 | Higher oxygen input Mouth-closed breathing Low inspiratory flow low tidal volume slow respiratory rate |
| What are factors that affect performance of low flow systems and decrease fi02 | Lower oxygen input mouth-open breathing high inspiratory flows High tidal volume fast respiratory rate |
| The air entrainment is a high flow device. It is also known as | Venti mask, Venturi mask |
| The Fi02 depends on? | The size of entrainment port Velocity of the gas |
| A blocked entrainment port on the venti mask will | increase the Fi02 |
| What are the Fi02 ranges for the venti mask? | 24%-60% |
| It might be difficult to provide fixed fi02 at high | Fi02 setting |
| Can the air entrainment mask be used with a bubble humidifier? | No, humidity must be proveided with bland aerosol set up attached to mask for humidity therapy |
| Are pediatric venti masks available? | yes |
| The jet orifice on the venti mask changes what 2 things? | Fi02 and Flow |
| If bed sheets cover the Venti Mask what happens? | The fi02 increases and the flow decreases |
| The air entrainment nebulizer is... | The large volume jet nebulizer |
| Fi02 and flow rate requirements on the air entrainment nebulizer depend on what? | The size of the air entrainment port |
| If the entrainment port becomes blocked or water condenses in the tubing what will happen with the air entrainment nebulizer? | The fi02 will increase |
| What are the fi02 ranges for the air entrainment nebulizer? | 28%-98% |
| The air entrainment nebulizer can provide 21% by attaching what to the flow meter? | air |
| What attachments can be used with the air entrainment nebulizer? | aerosol mask, trach collar, face tent, t-tube, tents, and oxyhoods Pediatric sizes are available |
| What is one thing about high fi02 settings on the air entrainment nebulizer? | It can be difficult to provide a fixed fi02 at high fi02 settings. |
| What are some disadvantages of oxygen masks? | Claustrophobia Muffled Speech Difficulty eating and drinking Blocks vomitus in unconscious patient Potential suffocation hazard |
| How do you troubleshoot if no gas flow can be detected? | See if gas is turned on. Look for kinking in tubing look for a leak. |
| How do you troubleshoot patient constantly removing mas? | Try to find a comfortable option if possible. |
| How do you troubleshoot the resivoir bag collapsing during inhalation? | Increase the flow of oxygen |
| How do you troubleshoot the reservoir bag remaining inflated during inhalation? | Mask may not have a tight fit. Inspiratory valve jammed/reversed. Flow may be too high |
| How do you handle a patient that develops sores or irritation over face and ears? | Use rubber cushions |
| How do you troubleshoot the humidifier pop-off sounding? | Look for obstruction, kinking, flow may be too high |
| How do you troubleshoot no humidity/aerosol coming from the system? | Check the water level Look for faulty equipment. |
| What are factors used to select appropriate oxygen device? | Objectives of therapy (short term/long term) Performance characteristics of set up (high flow/low flow) Individual needs of the patient and patient characteristics. (Age, LOC, Breathing Pattern, Presence or absense of a tracheal airway) |
| Oxygen blenders | Replace manual titration of fi02 using an oxygen and airflow meter. |
| How are oxygen blenders powered? | Pneumatically |
| Oxygen blenders can | achieve any fi02 |
| What does the oxygen blender contain? | A proportioning module for blending oxygen and air. |
| The oxygen blender has one alarm. What does it do? | Notify in case of loss of gas supply |
| Other things for oxygen blenders | It's accurate and precises Requires 50 PSI source Flow meter attachments are available |
| What are the two most common analyzers used in respiratory care? | Electrochemical Galvonic fuel cell |
| Electrochemical | Polarographic (Clark)electrode Commonly used in ABG machines and transcutaneous monitors Requires a battery for power |
| The electrochemical, polarographic clark electrode | has a 10-30 second response time, |
| The galvonic fuel cell | Is commonly used in ventilators and hand held analyzers |
| The galvonic fuel cell gets a result in | 60 seconds and needs no external power |
| The galvonic fuel cell will require calibration. | It uses 21% or 100% calibration gases |
| The galvonic fuel cell may be one point or two point calibration. | One point- Room Air Two Point- Room air and 100% Oxygen |
| Hyperbaric therayp | Inreases the pa02 wound healing around since the 1600's Based on boyles law |
| Indications of hyperbaric therapy | Air embolism C02 poisoning Wound Healing |
| Hazards of hyperbaric therapy | Tempanic Membrane rupture. |
Created by:
kparkerlehman
Popular Respiratory Therapy sets