RAD121 Word Scramble
V U M U C A
|
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
| Question | Answer |
| Why do the ball bearings between the rotor cuff and the anode shaft use silver plating as their lubrication? | Liquids produce gas at high temperatures and reduce the vacuum in the tube. |
| Actual Focal Spot | The physical area of the focal track that is impacted |
| Grid-Biased Tube | A type of tube that quickly regulates the flow of electrons, producing x-ray photons; also: grid-controlled, grid-pulsed |
| What is the actual focal spot controlled by? | --1.filament size--2.angle of anode |
| Define leakage radiation. | Any photon that escapes from the housing except at the port. |
| Radiographic Tube Rating Chart | A guide regarding the most common technical factor combinations that can be used without overloading the tube; also: tube rating chart |
| What is the purpose of the filament? | To provide sufficient resistance to the flow of electrons so that the heat produced will cause thermionic emission to occur. |
| What does the dielectric oil do? | --1.Insulates--2.Promotes cooling |
| What is different about a stress-relieved anode? | Does not require an elaborate tube warm-up procedure. |
| Why is tungsten the best metal for the x-ray source? | --1.It has a high melting point--2.is difficult to vaporize--3.high atomic number enhances diagnostic x-ray photos--4.heat-conducting ability |
| The envelope of x-ray tubes can be made from what? | metal or glass |
| Extrafocal Radiation | Photons that were not produced at the focal spot; also called off-focus radiation |
| What 3 functions does the anode have? | --1.provides a target surface--2.conducts high voltage--3.primary thermal conductor |
| What is the protective housing made of? | lead-lined cast steel |
| Rotating Anode | An anode assembly that turns during exposure |
| What must x-rays be a part of to be considered useful? | the primary beam |
| Why is it necessary for a vacuum to exist within the envelope? | This permits electrons to flow without encountering the gas atoms of air. |
| Why is molybdenum used as the primary target material for mammography x-ray tubes? | It's ability to emit a more uniform range of lower energy photons which permit better soft tissue imaging. |
| What are the basic parts of a cathode assembly? | filament/s, focusing cup, associated wiring |
| Leakage Radiation | Any photons that escape from the housing except at the port |
| Molybdenum's atomic number | 42 |
| Effective Focal Spot | The area of the focal spot that is projected out of the tube toward the object being radiographed. |
| isotropically | in all directions |
| Protective Housing | The entire cathode and anode assembly is housed within this metal structure |
| What materials, other than tungston, could be used to make the filament? | Rhenium and molybdenum |
| What is saturation current? | Once the current reaches a certain kVp, increasing kVp will not produce more electrons. |
| Focal Spot | The portion of the anode where the high-voltage electron stream will impact; also: target, focus, focal point, actual focal spot |
| Fractional Focal Spot | A very small focal spot; usually a fraction of a millimeter in size |
| Grid-Controlled Tube | A type of tube that quickly regulates the flow of electrons, producing x-ray photons; also: grid-biased, grid-pulsed |
| Wiring | The parts within the cathode assembly that connect the elements of the assembly together |
| What is the purpose of the cathode? | to produce a thermionic cloud, conduct high voltage to the gap from the cathode to the anode, and focus the electron stream as it heads for the anode |
| Focusing Cup | A shallow depression in the cathode assembly designed to house the filament |
| Vaporized tungston deposits on the inner surface of the glass envelope can cause what? | high-voltage arcing, and decreased efficiency. |
| What is the purpose of the focusing cup? | This narrows the stream as it goes to the anode. |
| Excessive heat results in what? | reduced x-ray tube life |
| What is the space charge effect? | During thermionic emission, electrons build at the filament and oppose production of more electrons. |
| Dual Focus | A two-filament arrangement within the x-ray tube. |
| Why does diagnostic radiography utilize rotating anodes? | because of their greater efficiency |
| What is the alloy called that is used in the filament? | Thoriated Tungston |
| What are stationary anodes composed of? | rhenium-alloyed tungston imbedded in a 45-degree angled copper end of a copper rod. |
| Pitting of the focal track is caused by what? | vaporization of focal track material; reduces efficiency |
| What is filament length? | 7-15 mm |
| Where are grid-biased tubes found? | capacitor discharge units and angiography units |
| What is the advantage of a graphite backed anode? | You can double the heat-loading capacity without increasing bearing wear. |
| How is off-focus radiation produced? | Photons strike another object in the tube (cathode assembly, vaporized metal on a glass envelope, off-target sites on the anode, etc.).This is composed of photons that were not produced at the target. |
| What is the glass envelope window made of in mammography tubes? | berylium |
| Filament | A small coil of thin thoriated tungsten wire |
| How does the anode heel affect radiation intensity? | Due to the geometry of this, the radiation intensity is greater on the cathode side. |
| Stationary Anode | An anode assembly that is immobile |
| kVp controls what? | The acceleration of the electrons from the cathode to the annode. |
| Why is metal becoming a more common choice for envelopes? | they eliminate the problem of tungston erosion |
| What is the point source of x-ray photons in addition to being the point that OID and SID are measured from? | the target |
| What are the three most impertant factors set by the radiographer? | kVp, mA, and time |
| What is the focusing cup made from? | nickel |
| What is the envelope made of? | pyrex or metal |
| Grid-Pulsed Tube | A type of tube that quickly regulates the flow of electrons, producing x-ray photons; also: grid-controlled, grid-biased |
| Biased focusing cup | causes exiting electron beam to be focused into a narrower stream |
| What is the function of the cathode? | to produce a thermionic cloud |
| Focal Point | The portion of the anode where the high-voltage electron stream will impact; also: target, focus, focal spot, actual focal spot |
| What is filament thickness? | .1-.2 |
| Rules of the Line Focus Principle | --1.As the actual focal-spot size increases, the effective focal spot size increases--2.When the target angle is less than 45-degrees, the effective focal spot is smaller than the actual focal spot. |
| What is filament width? | 1-2 mm |
| What is the purpose of the focal cup? | It narrows the electron stream as it goes to the anode. |
| What is purpose of the protective housing? | --1.Controls leakage and scatter radiation--2.Isolates high voltages--3.Provides a means to cool the tube--4.Provides cushioning from rough handling by operators. |
| Where are high speed incident electrons from the filament suddenly stopped? | the anode |
| What is the purpose of an anode warm-up procedure? | raises heat to near operating range to prevent cracking; helps maintain strong vacuum. |
| Envelope | The entire cathode and anode assembly is housed within this glass or metal structure |
| What are rotating anode disks composed of? | Molybdenum with the target focal track material being rhenium-alloyed tungsten backed by a thicker layer of molybdenum or graphite. |
| Focus | The portion of the anode where the high-voltage electron stream will impact; also: target, focal point, focal spot, actual focal spot |
| mA controls what? | The # of electrons available. |
| Stationary anodes are limited to what? | Low-power functions, such as those of dental units |
| What is a common cause of tube failure? | Bad bearings because of long use at high temperatures. |
| What is the rule for leakage radiation limit? | LEAKAGE RADIATION MUST BE LIMITED TO 100mR/hr @ 1 METER!!! |
| What is the purpose of grid-biased tubes? | Gives precise control of the thermionic cloud. Changes charge of focusing cup from negative to positive to stop electrons from flowing. |
| What is the target angle range for x-ray tubes? | 7-17 degrees |
| Where are stators? | Outside the envelope. |
| Housing Cooling Chart | Permits the calculation of the time necessary for the housing to cool enough for additional exposures to be made |
| Space Charge Effect | As more and more electrons build up in the area of the filament, their negative charges begin to oppose the emission of additional electrons |
| What are the 3 ways heat is dissapated? | --1.Radiation(99%)--2.Conduction--3.Convection |
| What benefit does rhenium provide? | greater elasticity when the focal track expands rapidly due to intense heat |
| Anode Assembly | Consists of the anode, stator, and rotor |
| Rotor | A hollow copper cylinder or cuff that is attached to the anode disk by a molybdenum shaft |
| What additional devices might help cool the housing/oil? | --1.fan--2.heat exchanger |
| Saturation Current | Filament phenomenon; as kVp increases, a greater percentage of the thermionically emitted electrons are driven toward the anode and is reached when there are no further thermionic electrons to be driven toward the anode; effects efficiency |
| Target | The portion of the anode where the high-voltage electron stream will impact; also: target, focus, focal spot, actual focal spot |
| What is the advantage of a high-speed rotor? | Faster anode rotation promotes better heat dissipation. |
| Anode Heel Effect | Due to the geometry of the angled anode target, the radiation intensity is greater(20% more) on the cathode side; 25% fewer photons on anode side |
| What four conditions must exist for x-ray production to occur? | --1.source of electrons--2.appropriate target material--3.high voltage--4.a vacuum |
| Cathode | The negative side of the x-ray tube; produces a thermionic cloud, conducts the high voltage to the gap between the cathode and anode, and focuses the electron stream as it heads for the anode. |
| Tungsten's atomic number | 74 |
| What are stators? | Self-induction motor magnets that turn the anode. |
| How would a Rhenium Tungston alloy be used? | As anode target material. |
| Focal Track | The portion of the anode where the high-voltage electron stream will impact; when discussing a rotating anode this describes the circular path that will be impacted by the electron beam |
| Window | A structure where the primary x-ray beams exit the envelope, which allows for less absorption of scatter radiation |
| Cathode Assembly | Consists of the filament, focusing cup, and associated wiring. |
| Line-Focus Principle | Used to reduce the effective area of the focal spot |
| The focusing cup has what electrical charge? | negative |
| Anode Cooling Chart | Permits the calculation of the time necessary for the anode to cool enough for additional exposures to be taken. |
| Tube Rating Chart | Provides a guide regarding the maximum technical factor combinations for each filament of each tube that can be used without overloading the tube plotted in mA, kV, and time |
| What are the 2 types of anodes? | --1.stationary--2.rotating |
| What is the primary function of the envelope? | To maintain the vacuum. |
| Which anodes have a greater heat-loading capacity? | high-speed anodes |
| What is the effective focal spot controlled by? | --1.actual focal spot--2.target angle |
| Where is the window on the envelope? | Where the primary beam exits. |
| Most common diagnostic x-ray angle is what? | 12-degrees |
| Harmonics | Name of the tone a high-speed rotating cuff makes at 5000-7000 rpm capable of shattering the glass envelope. |
| Space Charge Cloud | The ejection of electrons from the surface of the wire due to increased heat, causing an electron cloud; also: thermionic emission, electron cloud |
| What are the 7 recommendations for extending tube life? | --1.Anode warm-up procedure--2.Depress rotor switch in one motion--3.lower mA stations--4.lower-speed rotor--5.Repeated exposures near tube loading limits should not be made--6.Rotate tube housing gently--7.Don't use the tube if rotor bearings are loud. |
| Recorded detail are impacted by what? | Filament length and width. |
| Explain the space charge effect. | During thermionic emission the electrons build in the area of the filament and their negative charges oppose the production of more electrons |
| Anode | The positive side of the x-ray tube; serves as a target surface for high-voltage electrons from the filament, conducts the high voltage from the cathode back into the x-ray generator circuitry, and serves as the primary thermal conductor. |
| What are 2 causes of tube failure? | --1.tube arcing--2.filament breakage |
| Stator | Mutual-induction-motor electromagnets that turn the anode |
| Off-Focus Radiation | Photons created somewhere in the tube other than the focal spot; can cause ghosting; not a result of scatter from patient; exit through tube window |
| Of what is the rotor composed and how is it attached? | the rotor is a copper cuff attached to the anode disk by a molybdenum shaft. |
| Explain the line-focus principle. | When there is a decrease in the anode angle, there will be a decrease in the effective focal spot. When there is an increase in the anode angle, there will be an increase in the effective focal spot. |
Created by:
queenxraynay
Popular Radiology sets